Mushkin PC4000 High Performance: DDR500 PLUS

by Wesley Fink on 9/26/2003 11:49 AM EST
POST A COMMENT

11 Comments

Back to Article

  • Anonymous User - Sunday, October 05, 2003 - link

    Please start testing this goodness on a Athlon XP2500+ Barton. I have no problem reaching 240FSB on my ABIT NF7 S.V2 XP2500 Barton setup Reply
  • Anonymous User - Wednesday, October 01, 2003 - link

    Still dissapointed that you didnt test with Athlon. Would it have hurt? Just to see what happened? Reply
  • Parasitic - Wednesday, October 01, 2003 - link

    Dear audience and the reviwer,

    I just feel that nForce2 users are overlooked by this review - not to say that this isn't a great one, another excellent job by the staff.

    However, I resent the criticism on that AMD users have no need for DDR500. With the new Bartons and nForce2 400/Ultra chipsets, DDR400 and above have become popular in the eyes of system builders.

    Given the proper SPP voltage on the nForce2 or nForce2 400/Ultra, most unlocked processors like Thoroughbreds can hit pretty close to the 200MHz barrier, and it's a necessity to utilise DDR400 at that point. Like I mentioned earlier, with Bartons the road to 200FSB has become easier to walk on. Excuse my exaggeration, but it is almost a sin not to run Bartons beyond the 200FSB.

    If a futher investigations are looked, a lot of enthusiasts are purchasing, at a minimum, low-latency DDR400, with PC3500/PC3700 being the norm. This also applies to AMD users especially those of us with nForce2.

    Given the PCI lock, nForce2 is the overclocker's jewel for AMD setups. A group of us have already breached 233FSB, with occasional news of reaching 250FSB. Some motherboards even offer up to 300MHz of FSB adjustment in 1MHz increments.

    I understand that Intel's Canterwood and Springdale are highly popular in the top-end crowd right now; but a study on DDR500 should not be overlooked by the staff of Anandtech, one of the more respected and popular tech sites on the web. Please spare the "what about the commoners" criticism - we are tech-savvy people, and given that we voluntarily choose to read tech sites like Anandtech already introduces a bias into the popular of users reading critical on memory sticks.

    Thank you for your attention.
    Reply
  • Anonymous User - Monday, September 29, 2003 - link

    Guys the new OCZ PC4000 Universal ram is here.I have the new PC4000 that runs 2-3-3-5 at ddr400 and tops out well over ddr533 with 2.5-4-4-7 timings.At the moment though I still feel OCZ3700 is the fastest at 250fsb with 2-3-3-7 timings at 3Vdimm.

    Anyway, excelent review as usual Wes, keep up the good work.


    Tony
    Reply
  • Anonymous User - Sunday, September 28, 2003 - link

    The quality if geil ram is questionnable. Also they have poor consumer service. Reply
  • DragonReborn - Saturday, September 27, 2003 - link

    Any reason not to get the Geil 4200 over the 4000 with a 2.4/Watercooled setup? The geil is the only reasonably priced ram... Reply
  • Wesley Fink - Friday, September 26, 2003 - link

    DDR500+ Memory is currently an Intel 865/875 need. Myshkin tests DDR500 performance on Intel 865/875 boards and tests DDR400 performance on nForce2, Intel, and VIA chipsets.

    We ONLY tested this memory on an Intel platform. After testing, however, it perfroms fast enough at DDR400 that it could be a good choice for nF2 boards - with headroom for the future.
    Reply
  • TheInvincibleMustard - Friday, September 26, 2003 - link

    On the bottom of page 3, you state that performance on an Athlon nForce2 Ultra 400 was not tested for the Mushkin PC4000, but one page previous you say that it IS tested on an nForce2 Ultra 400 ... is that because those are what Mushkin tests the memory on itself, or was this a misprint of some sort? The only things you tested this memory on were the Intel-based boards listed at the bottom of page 3, correct? Reply
  • Wesley Fink - Friday, September 26, 2003 - link

    We have looked at OCZ 4000 Gold, but we did not do another review because performance was virtually identical to the OCZ4000 Copper Engineering Samples we tested in an earlier review. It is outstanding DDR500 memory and produced the highest overclock in our DDR500 roundup. However, it does not perform as fast at DDR400 as the Mushkin PC4000 High Performance tested here, Corsair XMS4000 PRO, or OCZ 3700 GOLD (which is based on lasered Samsung chips and not Hynix). We have asked OCZ about products using the newest Hynix chips, and they say they will likely release a similar product, or maybe something even faster, in the near future. Reply
  • Anonymous User - Friday, September 26, 2003 - link

    p.s. i forgot ocz pc4000 gold is available over here http://www.hardcorecooling.us/product.asp?0=200&am... Reply
  • Anonymous User - Friday, September 26, 2003 - link

    good job guys! you keep me up-to-date wth all new memory releases and their performence, or most of all. i do not realize why you guys do not except the existence of ocz pc4000 dual channel Gold. it will most probably perform as goog as pc3700 gold at ddr400. it is officialy clocked at ddr500 and will most probably overclock as good as ocz 4000 copper. i just can't stand lating any more to see it in action. Reply

Log in

Don't have an account? Sign up now