In and Around the Antec Eleven Hundred

It doesn't make too much sense to keep belaboring the comparison between Antec's P280 and the Eleven Hundred because as I discovered in the process of working on this review, there are some major differences between the two. The front bezel of the Eleven Hundred is almost completely ventilated, and that includes the shields for the 5.25" drive bays. It's actually a bit surprising that Antec didn't include any front-mounted intake fans, but given the basically wide-open-but-not-really design of the fascia coupled with the massive 200mm exhaust fan in the top of the enclosure, the Eleven Hundred may simply not need them in its default configuration.

One of the elements I especially like about the Eleven Hundred is the I/O port and button placement: the ports along the top front of the face and the power button and reset button on the front of the top of the enclosure show that Antec understands and expects the case to be placed on the floor, but doesn't force you to pick a side for you to set it. When you do get to the top, you'll see that 200mm exhaust fan. It glows bright blue, but thankfully the LEDs can be toggled off depending on your taste.

The side panels are fairly interesting. On the left side, Antec includes a window, pegs, and silicone grommets for mounting a pair of 120mm fans laterally. These intakes are lined up pretty specifically with where you can expect multiple graphics cards to be, and there's no side intake for the CPU cooling. Instead, there's a spacious panel behind the motherboard tray that's slightly bowed out to make it easier to route cables, but also a 120mm fan mount designed to intake cool air against the back of the CPU socket.

Both side panels are mounted using thumbscrews, and they're hinged rather than needing to be lined up and slid onto the chassis, making it much easier for the end user to close up shop. Removing them reveals the interior of the Eleven Hundred, which features the usual rubber-lined cable routing holes around the motherboard tray along with a sizable cutout for heatsink mounting brackets. The drive cage features six mounts for 3.5" drives (using rails included with the enclosure that snap into the drive's sides securely) and two toolless mounts for 2.5" drives. There are also four internal 120mm fan mounts; two are in the front of the enclosure (the front fascia is easy to snap on and off) while two are actually inside the case, behind the drive cage.

All told, I personally find the aesthetic of the Eleven Hundred to be a lot tamer than many of the other gaming cases Antec sells. I liked how the P280 looked, and even though the Eleven Hundred is much tarted up, it's still not the plastic-and-LED "gamer-oriented" design the Six Hundred and Nine Hundred series have. Internally, it looks relatively easy to assemble, too, and certainly spacious enough without outright wasting real estate.

Introducing the Antec Eleven Hundred Assembling the Antec Eleven Hundred
POST A COMMENT

39 Comments

View All Comments

  • Stahn Aileron - Monday, April 09, 2012 - link

    Would it be too much to ask that you actually place the ambient tempurature during testing somewhere on the graphs themselves so we have a readily accessible reference point right there on the graphs? It would also work as a reminder to readers what the conditions are. Reply
  • Dustin Sklavos - Monday, April 09, 2012 - link

    The ambient temperature is going to vary from test system to test system, that's why I switched to listing the delta. Reply
  • Rick83 - Monday, April 09, 2012 - link

    You did check, that the delta is a constant over ambient temperature though, did you? It may not be for every case. Also, of course, fan speeds will be impacted by ambient/internal temperature.

    If you can, you should probably run two series of tests, one in the morning and one in the evening, and then either average that or use one measurement, but at least comment the other. At least for noise, we need ambient temperature, as otherwise that value is completely without base for comparisons.
    Reply
  • kandrtech - Monday, April 09, 2012 - link

    Those familiar with thermodynamics, and the equations utilized, would agree that the delta approach is the best. Variances of a few (or 10) degrees on ambient will not appreciably change the delta results. By appreciably, I mean you'll see differences out to one or more decimal places . . . . Reply
  • niva - Monday, April 09, 2012 - link

    Are you talking 10 deg C or F?

    Ideally your ambient temperature should be somewhere in the +/- 5 deg of 70 deg F. These are the normal temperatures most households are kept at. There may be a significant difference between the noise produced by components at 65 deg F, and someone's house which may be normally kept at 85 deg during the summer daytime because of lack of AC?

    And I'm talking about idle situation here...

    The point was valid, just include the temperature in your test data.
    Reply
  • bobbozzo - Monday, April 09, 2012 - link

    The article describing their new methodology for case testing seems to indicate that ambient temps are maintained between 71-74F.

    http://www.anandtech.com/show/5709/introducing-our...
    Reply
  • ShieTar - Tuesday, April 10, 2012 - link

    But those familiar with modern PC design are aware that fan-control systems generally try to achieve a constant CPU/GPU-temperature. Thus when you raise the ambient temperature to somewhat higher levels, CPU/GPU fans tend to speed up, giving you lower Delta-T values at increased noise.

    Thus it is important to still run these tests at comparable ambient temperatures, and if this is indeed checked at each test, it should be no problem to change the title of the temperature graph to read "Delta over ambient at 20+/-2°C". Or whichever is the range that is controlled and accepted by the tester.
    Reply
  • O8h7w - Saturday, April 14, 2012 - link

    I feel perfectly good about showing the temperature as delta above ambient instead of absolute temperature. But it seems many readers would like to see the ambient temperature at the time of testing reported as well, and I have to agree.

    The way of doing this that would make perfect sense in the graphs is to modify the labels to look like this:
    Antec 1100
    @ 23°C ambient
    Reply
  • Lucian2244 - Monday, April 09, 2012 - link

    Good review, i was wondering how it would look with a mATX in there.
    Is it just me or their cases get uglier and uglier ?
    Reply
  • Iketh - Monday, April 09, 2012 - link

    It's not you... this case is ugly... AND stupid...

    Enough with filterless side vents already! Why even have side vents? That's a damn 80's design, speaking figuratively...
    Reply

Log in

Don't have an account? Sign up now