Test Configuration and Settings

For our testing, we used the following system.

Memory Benchmarking System Configuration
CPU Intel Core i7-2600K (Stock with Turbo Boost enabled: 3.5GHz - 3.8GHz)
Motherboard ASUS P8P67 Pro - BIOS version 1502
Memory Patriot Viper Extreme Division 2 4GB (2x2GB) DDR3-2133 Kit
Graphics MSI GTX 580 Lightning - Stock clocks (832MHz/1050MHz)
SSD OCZ Agility 2 120GB
PSU Corsair HX850 Power Supply
OS Microsoft Windows 7 Professional 64-bit

You’ll notice that we list only one specific set of memory; I don't have specifically rated modules for each of the memory speeds tested. Instead, I used a pair of DDR3-2133 modules that worked flawlessly at all of the lower speeds. Thanks to Patriot for supplying the DDR3-2133 4GB kit used for today's testing. To ensure my results weren't skewed, I tested a pair of DDR3-1600 CL9 modules against the DDR3-2133 CL9 modules running at the lower DDR3-1600 CL9 speed. The results of this test were identical. There may be minor variations between memory brands, but as a baseline measurement of what to expect our testing will be sufficient. We then used the following clock speeds and timings:

Tested Memory Speeds
DDR3-1333 7-7-7-18-2T
8-8-8-18-2T
9-9-9-18-2T
DDR3-1600 7-8-7-21-2T
8-8-8-21-2T
9-9-9-21-2T
DDR3-1866 8-9-8-24-2T
9-9-9-24-2T
DDR3-2133 9-11-9-27-2T

Testing Procedures

Each of the tests were performed three times with the average of those three runs used for the final results. However, there were a few exceptions to this. First, PCMark 7 was only ran once because it loops three times before providing its score. Second, the x264 HD Benchmark was only ran once because it looped four times in a single run. Third and finally, the LINPACK Benchmark was looped twenty-five times because it was also used to test for stability. And with that out of the way, let’s get to the test results.

Investigating Sandy Bridge Memory Scaling AIDA64 Memory Benchmark
POST A COMMENT

76 Comments

View All Comments

  • Rick83 - Monday, July 25, 2011 - link

    Do they take into account, that we should be using 1.5V DIMMs for Sandy Bridge?

    The addition of that requirement usually limits choice quite a bit.
    Reply
  • compudaze - Monday, July 25, 2011 - link

    The SNB datasheet does suggest that the max memory voltage is 1.575V, however, many motherboard and memory manufactures state that they haven't had any problems with memory running at 1.65V on SNB. Reply
  • compudaze - Monday, July 25, 2011 - link

    Also, if you stick to the spec sheet, you shouldn't be running faster than DDR3-1333 memory. Reply
  • Taft12 - Monday, July 25, 2011 - link

    You should be using 1.5V DIMMs anyway - if a memory OEM needs 1.65V to achieve the same speed and timings another vendor does at 1.5V, it's inferior memory. Reply
  • jdogi - Monday, July 25, 2011 - link

    Just as your daily driver vehicle is likely inferior to a Mercedes or Ferrari. You should get a new car. You should not make any attempt to balance cost with the value. Just get the best. It's the only way to go. What's best for Taft is best for all.

    ;-)
    Reply
  • Iketh - Tuesday, July 26, 2011 - link

    you didn't understand the logic Reply
  • MrSpadge - Wednesday, July 27, 2011 - link

    I'm sure he did. What Taft failed to mention was that "at the same price, you should be using the memory spec'ed for less voltage". However, if some memory needs a little more voltage, but is way cheaper - balance cost and value.

    MrS
    Reply
  • Rick83 - Wednesday, July 27, 2011 - link

    Actually, the higher voltage is out of spec for the CPU memory controller and may wel impact longevity.
    So it's like buying the Ferrari, and running it on Biofuel with too much Ethanol that eats right through the tubing, but is marginally cheaper.
    Reply
  • jfelano - Tuesday, July 26, 2011 - link

    Not inferior, just older. All 1600mhz memory was 1.65v when it debuted. Then they came out with 1.5v, now even 1.35v. Reply
  • cervantesmx - Thursday, July 28, 2011 - link

    That is correct indeed. Just purchased 8GB at 1600mhz running on 1.25v. $59.99. Free shipping. Reply

Log in

Don't have an account? Sign up now